代码拉取完成，页面将自动刷新
See Getting Started with the Raspberry Pi Pico and the README in the pico-sdk for information on getting up and running.
| App | Description | Link to prebuilt UF2 |
|---|---|---|
| hello_serial | The obligatory Hello World program for Pico (Output over serial version) | |
| hello_usb | The obligatory Hello World program for Pico (Output over USB version) | https://rptl.io/pico-hello-usb |
| blink | Blink an LED on and off. | https://rptl.io/pico-blink |
| App | Description |
|---|---|
| hello_adc | Display the voltage from an ADC input. |
| joystick_display | Display a Joystick X/Y input based on two ADC inputs. |
| adc_console | An interactive shell for playing with the ADC. Includes example of free-running capture mode. |
| App | Description |
|---|---|
| hello_48MHz | Change the system clock frequency to 48 MHz while running. |
| hello_gpout | Use the general purpose clock outputs (GPOUT) to drive divisions of internal clocks onto GPIO outputs. |
| hello_resus | Enable the clock resuscitate feature, "accidentally" stop the system clock, and show how we recover. |
| App | Description |
|---|---|
| build_variants | Builds two version of the same app with different configurations |
| App | Description |
|---|---|
| hello_dma | Use the DMA to copy data in memory. |
| control_blocks | Build a control block list, to program a longer sequence of DMA transfers to the UART. |
| channel_irq | Use an IRQ handler to reconfigure a DMA channel, in order to continuously drive data through a PIO state machine. |
| App | Description |
|---|---|
| cache_perfctr | Read and clear the cache performance counters. Show how they are affected by different types of flash reads. |
| nuke | Obliterate the contents of flash. An example of a NO_FLASH binary (UF2 loaded directly into SRAM and runs in-place there). A useful utility to drag and drop onto your Pico if the need arises. |
| program | Erase a flash sector, program one flash page, and read back the data. |
| xip_stream | Stream data using the XIP stream hardware, which allows data to be DMA'd in the background whilst executing code from flash. |
| ssi_dma | DMA directly from the flash interface (continuous SCK clocking) for maximum bulk read performance. |
| App | Description |
|---|---|
| hello_7segment | Use the GPIOs to drive a seven segment LED display. |
| hello_gpio_irq | Register an interrupt handler to run when a GPIO is toggled. |
| dht_sensor | Use GPIO to bitbang the serial protocol for a DHT temperature/humidity sensor. |
See also: blink, blinking an LED attached to a GPIO.
| App | Description |
|---|---|
| hello_divider | Show how to directly access the hardware integer dividers, in case AEABI injection is disabled. |
| App | Description |
|---|---|
| bus_scan | Scan the I2C bus for devices and display results. |
| lcd_1602_i2c | Display some text on a generic 16x2 character LCD display, via I2C. |
| mpu6050_i2c | Read acceleration and angular rate values from a MPU6050 accelerometer/gyro, attached to an I2C bus. |
| App | Description |
|---|---|
| hello_interp | A bundle of small examples, showing how to access the core-local interpolator hardware, and use most of its features. |
| App | Description |
|---|---|
| hello_multicore | Launch a function on the second core, printf some messages on each core, and pass data back and forth through the mailbox FIFOs. |
| multicore_fifo_irqs | On each core, register and interrupt handler for the mailbox FIFOs. Show how the interrupt fires when that core receives a message. |
| multicore_runner | Set up the second core to accept, and run, any function pointer pushed into its mailbox FIFO. Push in a few pieces of code and get answers back. |
| App | Description |
|---|---|
| blinky | Blink "hello, world" in Morse code on Pico's LED |
| button | Use Pico's BOOTSEL button as a regular button input, by temporarily suspending flash access. |
| App | Description |
|---|---|
| hello_pio | Absolutely minimal example showing how to control an LED by pushing values into a PIO FIFO. |
| apa102 | Rainbow pattern on on a string of APA102 addressable RGB LEDs. |
| differential_manchester | Send and receive differential Manchester-encoded serial (BMC). |
| hub75 | Display an image on a 128x64 HUB75 RGB LED matrix. |
| i2c | Scan an I2C bus. |
| logic_analyser | Use PIO and DMA to capture a logic trace of some GPIOs, whilst a PWM unit is driving them. |
| manchester_encoding | Send and receive Manchester-encoded serial. |
| pio_blink | Set up some PIO state machines to blink LEDs at different frequencies, according to delay counts pushed into their FIFOs. |
| pwm | Pulse width modulation on PIO. Use it to gradually fade the brightness of an LED. |
| spi | Use PIO to erase, program and read an external SPI flash chip. A second example runs a loopback test with all four CPHA/CPOL combinations. |
| squarewave | Drive a fast square wave onto a GPIO. This example accesses low-level PIO registers directly, instead of using the SDK functions. |
| st7789_lcd | Set up PIO for 62.5 Mbps serial output, and use this to display a spinning image on a ST7789 serial LCD. |
| uart_rx | Implement the receive component of a UART serial port. Attach it to the spare Arm UART to see it receive characters. |
| uart_tx | Implement the transmit component of a UART serial port, and print hello world. |
| ws2812 | Examples of driving WS2812 addressable RGB LEDs. |
| addition | Add two integers together using PIO. Only around 8 billion times slower than Cortex-M0+. |
| App | Description |
|---|---|
| hello_pwm | Minimal example of driving PWM output on GPIOs. |
| led_fade | Fade an LED between low and high brightness. An interrupt handler updates the PWM slice's output level each time the counter wraps. |
| measure_duty_cycle | Drives a PWM output at a range of duty cycles, and uses another PWM slice in input mode to measure the duty cycle. |
| App | Description |
|---|---|
| hello_reset | Perform a hard reset on some peripherals, then bring them back up. |
| App | Description |
|---|---|
| hello_rtc | Set a date/time on the RTC, then repeatedly print the current time, 10 times per second, to show it updating. |
| rtc_alarm | Set an alarm on the RTC to trigger an interrupt at a date/time 5 seconds into the future. |
| rtc_alarm_repeat | Trigger an RTC interrupt once per minute. |
| App | Description |
|---|---|
| bme280_spi | Attach a BME280 temperature/humidity/pressure sensor via SPI. |
| mpu9250_spi | Attach a MPU9250 accelerometer/gyoscope via SPI. |
| spi_dma | Use DMA to transfer data both to and from the SPI simultaneously. The SPI is configured for loopback. |
| spi_flash | Erase, program and read a serial flash device attached to one of the SPI controllers. |
| App | Description |
|---|---|
| hello_double_tap | On dev boards with a reset button (but no BOOTSEL), a magic number in RAM can be used to enter the USB bootloader, when the reset button is pressed twice quickly. |
| narrow_io_write | Demonstrate the effects of 8-bit and 16-bit writes on a 32-bit IO register. |
| unique_board_id | Read the 64 bit unique ID from external flash, which serves as a unique identifier for the board. |
| App | Description |
|---|---|
| hello_timer | Set callbacks on the system timer, which repeat at regular intervals. Cancel the timer when we're done. |
| periodic_sampler | Sample GPIOs in a timer callback, and push the samples into a concurrency-safe queue. Pop data from the queue in code running in the foreground. |
| timer_lowlevel | Example of direct access to the timer hardware. Not generally recommended, as the SDK may use the timer for IO timeouts. |
| App | Description |
|---|---|
| hello_uart | Print some text from one of the UART serial ports, without going through stdio. |
| uart_advanced | Use some other UART features like RX interrupts, hardware control flow, and data formats other than 8n1. |
| App | Description |
|---|---|
| dev_audio_headset | Audio headset example from TinyUSB |
| dev_hid_composite | Composite HID (mouse + keyboard) example from TinyUSB |
| dev_hid_generic_inout | Generic HID device example from TinyUSB |
| dev_lowlevel | A USB Bulk loopback implemented with direct access to the USB hardware (no TinyUSB) |
| App | Description |
|---|---|
| host_hid | Use USB in host mode to poll an attached HID keyboard (TinyUSB example) |
| App | Description |
|---|---|
| hello_watchdog | Set the watchdog timer, and let it expire. Detect the reboot, and halt. |
此处可能存在不合适展示的内容，页面不予展示。您可通过相关编辑功能自查并修改。
如您确认内容无涉及 不当用语 / 纯广告导流 / 暴力 / 低俗色情 / 侵权 / 盗版 / 虚假 / 无价值内容或违法国家有关法律法规的内容，可点击提交进行申诉，我们将尽快为您处理。
